[Perunka]

.
.
Download / Read Online Alv d2 manual
.
.
.

.
You are using an outdated browser. For a faster, safer browsing experience, upgrade for free today. You have no items in your shopping cart. These specifications cover the ALV2 ENTRANCE READER and if use with exclusive controller,it enable to output relay signal to the automatic door and control board of the electric key. When a contact less IC card issued by card issuing machine installed in the front desk isused, it collates the various information such as a Hotel cord and room number with storeddata. If the card is confirmed valid, it output the signal to the exclusive controller. Electrical SpecificationsPower supply3. Vdc is supplied from the exclusive controller. RH without condensationMiwa Lock Co. Bring a card key close to the ALV2 ENTRANCE READER. The ALV2 ENTRANCE READER reads the key data and if the data accords with thedatabase, voltage signal is sent to the exclusive controller. If the card key is valid, the LED lights green. In case of invalid card key, the LED lights red. This unit has been tested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonableprotection against harmful interference in a residential installation. This unit generates,uses, and can radiate radio frequency energy and, if not installed and used in accordancewith the instructions, may cause harmful interference to radio communications. However,there is no guarantee that interference will not occur in a particular installation. Reorient or relocate the receiving antenna. Increase the separation between the unit and receiver. Connect the unit into an outlet on a circuit different from that to which the receiver isconnected. This unit complies with Part 15 of the FCC Rules. This unit must accept anyinterference received, including interference that may cause undesired operation. LabellingMIWA LOCK ALV2 ENTRANCE READER is labelled as below. Top element. HRUNG Scope of Delivery, Unpacking and Inspection . WEEE, please contact your local distributor. Arrangements are made with the dealer where you purchased the. However, if you would rather face to allow for sufficient airflow during the operation. Before establishing the mains supply connection, please blem. Controls, Indicators and Connections 2. When connecting signal sources, please make sure to set the corresponding channel faders or at least the master faders to their minimum positions or engage the STANDBY switch. This will save you, your audience, and the equipment from extensive wear from unpleasant pops. EQ section allows very differentiated shaping of the incoming audio signal within miscellaneous frequency bands. Before you begin to alter the sound, all EQ controls should be set to their neutral position, i. Play the desired sound source or talk into the microphone. MON controls and the channel fader. Do not connect signal sources to phone and RCA inputs at the same time. If you use a keyboard as sound source on one of the stereo inputs, make sure that no split zones or layers with channel separation are activated. These controls determine the amount of the summed L and R signal that is sent to the MON 1 or MON 2 summing bus. The signal gets always split pre fader. To accomplish this function, the FX 1 and FX 2 ON switches have to be engaged. FX 1 or FX 2 to the AUX 1 or AUX 2 channel. FX 1 or FX 2 to the MON 1 or MON 2 channel. Experience has revealed that the effect level in the monitor mix has to be lower than the level in the master mix, since the distance between monitor speakers and artists is much shorter. POST button, it is also possible to configure the bus for monitoring purposes. FEEDBACK FILTER The feedback filter is a very narrow banded notch filter, which is only active in a range that is extremely susceptible for acoustical feedback. FILTER rotary control sets the corresponding frequency range. B, indicating the levels that are present at the master outputs in dBu. R signals for connection of the main PA. The MASTER outputs are switched via output relay with a delay of approx. For further information, please consult your local dealer. In case you want to have a clear and highly intelligible sound, which, as a side effect, provides the cymbals with more crisp, you should raise the levels of the 12 kHz or 6. Mac is used for playback purposes only. In this case the warning can be ignored. The CMS includes a premium OLED display. Compared to general LC displays the OLED display is brighter, has a greater contrast ratio and a wider viewing angle. Effect mode The start screen appears after switching the CMS on. Edit FX 1 Device Setup FX Control Setup Footswitch Ctrl. Edit FX 2 Display Brightness TAP Button Ctrl. QUALIZER OUTING Parameter Description Footswitch Ctrl. The 11 band Stereo Graphic Equalizer can be routed to units using a footswitch. This dialog allows selecting one of TAP Button Ctrl. Device Settings can be activated or deactivated. Parameter Value filexlib.
.
Alv d2 guide
Alv d2 brugervejledning
Alv d2 كتيب
Alv d2 instruction
Alv d2 bedienungsanleitung

[投稿者]

投稿