.
.
Download / Read Online 2003 yamaha v star 1100 service manual
.
.
.

.
How To Measure Torque Wrench Effective L. Transmission, Shift Mechanism and Middle. Fuel, Exhaust and Emission Control S. Fuel and Emission System Electrical Spec. Rear Suspension and Final Drive Torque S. On USA, California and Canada model. Do not operate the vehicle in an enclosed area. Handling Gasoline Safely in this section. Keep tools clean and in good condition. Keep the work area clean and organized. Wear the correct clothing for the job. Do not carry sharp tools in clothing pockets. Never use gasoline to clean parts. Top element. WARNINGS, CAUTIONS AND NOTES 10. Wear eye protection any time the safety of your eyes is in question. The terms WARNING, CAUTION and NOTE volving drilling, grinding, hammering, compressed have specific meanings in this manual. ID number is a variation of the VIN number. CHAPTER ONE Record these numbers in the Quick Reference Data section at the front of the book. Have these numbers available when ordering parts. Table 1 and Table 2 to identify a particular motorcycle. Refer to Table 7 for torque conversion factors and to Table 6 for general torque specifications. Using an oil with a different classification can cause engine damage. Full support Thin oils have a lower number while thick oils have Direction areas of thrust. CHAPTER ONE Brake fluid will damage plastic, painted or plated surfaces. Use extreme care when working with brake fluid. Immediately clean up any spills with soap and water. Rinse the area with plenty of clean water. Threadlocking Compound In the case of Yamaha special tools, two part numbers are listed. CHAPTER ONE The number stamped on the wrench refers to the distance between the work areas. This must match the distance across two parallel flats on the bolt head or nut. This reduces the chance of the tool slipping. GENERAL INFORMATION lows the user to install or remove the nut without removing the socket. CHAPTER ONE specifications in this manual provide an indication of the range required. A torque wrench is a precision tool that must be properly cared for to remain accurate. Store torque wrenches in cases or separate padded drawers within a toolbox. Effective length No calculation needed. The sharp jaws will damage the objects they hold. This chart represents the values of figures placed to the right of the decimal point. Clean the anvil and spindle faces. CHAPTER ONE Care Micrometers are precision instruments. They must be used and maintained with great care. Store micrometers in protective cases or separate padded drawers in a toolbox. When in storage, make sure the spindle and anvil faces do not contact each other or any other objects. CHAPTER ONE electrical basics is necessary to perform simple the circuit or component capacity, the system will diagnostic tests. Voltage Electrical Tests Voltage is the electrical potential or pressure in an Refer to Chapter Two for a description of various electrical circuit and is expressed in volts. GENERAL INFORMATION that carefully laid out parts will become disturbed, making it difficult to reassemble the components Filed correctly without a diagram. Make sure all shims and washers are reinstalled in the same location and position. Whenever a rotating part contacts a stationary part, look for a shim or washer. SCREWS AND BOLTS lessness or impact damage. GENERAL INFORMATION sulting from friction. When installing a new bearing, take care to prevent damaging it. When installing a bearing as described in Step 1, Press arm some type of driver is required. Never strike the bearing directly with a hammer or the bearing will be damaged. GENERAL INFORMATION CAUTION Before heating the housing, wash the housing thoroughly with detergent and water. Rinse and rewash the cases as required to remove all traces of oil and other chemical deposits. Improper removal of a seal can damage the housing Dust lip or shaft. GENERAL INFORMATION riding time since the last service. Fill the engine This is especially important on a motorcycle as with the recommended type of oil. Star 1100 Classic Cast Wheel XVS1100A UK models XVS1100 Drag Star. California model Cubic centimeters Capacitor discharge ignition Canada model Cubic inch displacement cu. CHAPTER TWO TROUBLESHOOTING Begin any troubleshooting procedure by defining the engine will not run. Gather as ing principles are described in Figure 1. The engine can start when the sidestand is up and the transmission is in neutral. Perform each step while remembering the engine will jump, the stronger the ignition system. Use the operating requirements described in this chapter. Motion Pro Ignition System troubleshooting procedures in this chapter. CHAPTER TWO WARNING Make sure the spark plug is away from the spark plug hole in the cylin der so the spark cannot ignite the mix ture in that cylinder. If the engine is flooded, do not perform this test. The firing of the spark plug can ignite fuel ejected from the opened spark plug hole. Try starting the engine by following normal 4. Incorrect filexlib.
.
2003 yamaha v star 1100 handbog
2003 yamaha v star 1100 prirucka
2003 yamaha v star 1100 manuaalinen
2003 yamaha v star 1100 instruction manual
2003 yamaha v star 1100 handbuch